Do you screw a shower base to the studs?

Unlike concrete shower pans which bond to the floor and are held in place by cement, shower bases are held in place with screws. Connecting the shower base to the wall studs is part of the installation process to hold the pan in place.

How do you set a shower base in mortar?

Secure the Shower Pan Then position mounds of mortar on the marks. Position the shower base in the area, placing it onto the adhesive or mortar, and press firmly in place. Adjust the shower pan until it is level in all directions. Place cardboard or another material into the shower pan base to protect its surface.

How much mortar do you put under a shower base?

To set the base, mix up about half a 60-lb. bag of mortar with water to a creamy consistency. Avoid concrete mix; stones in the mix will hold the base away from the floor. Spread the mortar over the floor under the base, about 1 in. or so thick.

What do you put under a shower base?

Mortar is recommended to use under all shower pans. Mortar reduces the risk of your pan slipping or cracking from an uneven surface.

How thick should mortar be under shower pan?

Build the Primary Mortar Bed With the waterproofing membrane in place, it’s time to put the final layer of Sand Mix down. The depth of this layer will be determined by the height of the adjustable drain but must be a minimum of ½”.

Can I use thinset to level shower pan?

Using thin set to fill low areas by applying it a little thicker (most times it is much thicker) as the tile is being installed, is not a good idea. In fact, most manufacturers indicate in their product literature NOT to use thin set mortar to level or flatten the floor or wall.

What type of mortar do I use for shower pan?

The ideal mortar for a shower pan is a mix of standard cement mix with sand and Portland cement. This type of mortar creates a great water-resistant barrier that can support the weight of the shower unit.

Can you use spray foam under shower base?

Only a minimal-expanding foam should be used under a shower pan. The reason for this is that when foam expands it exerts pressure against opposing forces. And so, you could end up with bowing or even cracking of your shower pan.

How thick should mortar be for shower tray?

Seal the installation area with a suitable clear waterproofing agent. So that the tray is bedded completely level the tray area has to be FULLY COVERED with an 8mm minimum thickness of weak cement mix (Fig 3). The minimum thickness of mortar at the lowest point should be 5mm after the tray has been levelled.

What do you put under a shower pan?

Can I use thinset for shower floor?

Because thinset is not affected by moisture, it is best for floor tile and any tile in wet areas, including shower floors, walls, and ceilings and tub surrounds.

How to install a sterling shower base?


  • Latex modified thinset mortar
  • Notched trowel,1/4-inch
  • Drill and paddle
  • Drill screw attachments
  • Bucket
  • Wood screws
  • Pipe wrench
  • How to build a shower base?

    Measure and clean the place. Start with measuring the place where you want to install your new shower pan.

  • Install drainer and shower step/beam. After deciding which type of drain for a shower you want to use,you should start paying attention to the details.
  • Fill in the dry pan mixture.
  • Lay of shower pan material.
  • Make the floor smooth and flat.
  • How to install a corner shower base?

    Shower Base Install And Connect Drain Install You can find any of the items seen in this video Below and your purchase will help support this channel. Thank…

    How to install a concrete shower base?

    Make space for the drainpipe by removing concrete

  • Put the drainage tool and pipe in the hole
  • Ensure that the shower pan fits properly
  • Apply and spread mortar on the concrete base
  • Firmly set the shower pan in place on top of the mortar
  • Fix the drain
  • Wait for 24 hours until the mortar dries
  • Use silicone to seal the shower tray with the wall