What is the wing and drop system?
A wing-and-drop set is a set made up of shaped and painted 2D elements, usually fabric. These include vertical pieces on the side and horizontal pieces across the top. Together with a backdrop, they often include forced perspective to create the illusion of a grandiose interior or exterior.
What are shutters in theatre?
theatrical productions painted on two flats, called shutters, which met at the centre of the stage; and cloths that could be rolled up were occasionally used.
What is the chariot and pole system?
1641, when he perfected the chariot-and-pole system. According to this system, slots were cut in the stage floor to support uprights, on which flats were mounted. These poles were attached below the stage to chariots mounted on casters that ran in tracks parallel to the front of the stage.
What was developed during the Italian Renaissance as a way of moving scenery on and off?
Proscenium theatres, also known as picture frame stages, developed during the Italian Renaissance.
Why is it called upstage and downstage?
On a raked stage an actor who is farther from the audience is higher than an actor who is closer to the audience. This led to the theatre positions “upstage” and “downstage”, meaning, respectively, farther from or closer to the audience.
What is a stage light called?
Lantern: Though you may simply hear them referred to as lights or lighting fixtures, the lighting units used in stage lighting are also commonly called lanterns. In Europe, the more common term is luminaire.
What does DC stand for in theatre?
DC. (down centre) DL. (down left) Sometimes described as USL (up stage left), DS (down stage), etc.
Who invented the chariot-and-pole system?
Giacomo Torelli
Chariot-and-Pole System Giacomo Torelli, known as the Great Sorcerer for his spectacular scenic innovations, to design for the Palais Royal. Working at a theatre in Venice in the early 1640s, Torelli had already put together the first “chariot-and-pole” system for changing scenery.
Who created the chariot-and-pole system of moving and changing scenery?
From 1641 Giacomo Torelli developed and refined the chariot-and-pole, or carriage-and-frame, method of scene shifting. This was a mechanization of the groove system that allowed one person to change all the wings simultaneously.
What type of scenery did Italians develop?
Developed during the Italian Renaissance, perspective scenery applied the newly mastered science of linear perspective and brought the craft of illusion to the Italian stage.
Which is upstage and downstage?
Upstage: The back of the stage or part of the stage farthest from the audience. Downstage: The front of the stage or part closest to the audience. Stage Left: The left of the stage when facing the audience.
Which direction is upstage?
Defining Common Stage Directions The front of the stage, called downstage, is the end closest to the audience. The rear of the stage, called upstage, is behind the actor’s back, furthest from the audience.
What is an elevator stage?
elevator stage, drop stage, lift stage A theater stage floor which moves vertically on an elevator, usually so that one set can quickly replace another; may consist of a single unit or articulated sections.
What is a turntable in theater?
revolving stage, theatrical device for scene changes, or shifts, by which three or more settings are constructed on a turntable around a central pivot and revolved before the audience.
What is a DMX lighting system?
DMX is an acronym for Digital Multiplex. It is the standard digital communication protocol that is used to remotely control intelligent lighting fixtures.
What is a Jack in theater?
L-jacks are typically used to hold a piece of scenery in an upright position.
What is batten in theatre?
Also known as a pipe batten, a lighting batten is a steel pipe hung from rigging or dead hung from a building’s structure. Battens are used for attaching scenery, draperies, projections screens and lighting equipment. Typical stage battens are made from 1-1/2″ Schedule 40 Pipe.
What is the best shutter design software?
The Shutter Design Wizard program Rockler is quick, accurate and, best of all, free. Here’s a big reason to like this system: there’s almost no desk time required for planning or drawing your shutter project, thanks to the free Shutter Design Wizard program Rockler offers.
Where can I find printable shutter design plans?
A few mouse creates a complete set of printable plans for your shutter project. The Shutter Design Wizard program Rockler is quick, accurate and, best of all, free.
What is a shutter jig template?
The templates are clearly marked, sturdily made and make shutter construction essentially a drilling operation. (Note: for 1-1/4″ fixed-louver shutters, the stile jig is a template for routing short slots that house the ends of the louvers instead of using the pins.)
How do you attach louvers to a shutter frame?
It includes two jigs: a long one for drilling the stiles to accept plastic louver pins and metal clips that attach the louvers and control arms; and a shorter jig with adjustable stops that allows you to drill corresponding pin holes in the ends of the louvers. Movable louvers, as shown here, swivel on single pairs of pins inside the shutter frame.
https://www.youtube.com/watch?v=VjERVmfSV3g